Comma 15w40 Mineral Oil 4 x 5 Liter (20 Liters total) Pack offering a big saving on shipping costs.

This is the standard stuff that we normally use on our services, offering a higher viscosity than the recommended oil, 15w40 will help protect the inside of your engine better especially the stationary gear bearings (a key weak point on the RX-8 when using 5w30)

This oil is supplied in a 5 liter can and should be enough for a oil change plug 1-1.5 liters spare for top ups.

We recommend 3000-6000mile (or 6 months) oil changes to keep your oil as clean as possible.

Larger quantities are available please contact us for pricing

This Kit contains everything you will need to carry out the conversion from conventional coolant over to Evans Waterless Coolant on your Mazda RX-7 or RX-8.

Plus we are offering  5% Discount when purchasing this pack compared to purchasing everything individually.

This Kit Contains the following;

• 2 x 5 Litre bottles of Evans Prep Fluid.
• 2 x 5 Litre bottles of Evans Power Cool 180 Waterless Coolant.

This is the perfect starter pack to carry our a full conversion offered with a great bulk shipping discount.

Before using Evans Waterless coolant for the first time it is advised that Evans Prep fluid is used to flush the cooling system of ay remaining water based coolant, This is essential for a successful conversion to Evans Waterless coolant.

For more information on Prep Fluid and Power Cool 180 can be found in their individual product descriptions above.

Evans Prep Fluid MUST be used before Evans coolant is installed in your cooling system for the first time, when converting from traditional coolant.

Evans Prep Fluid is specifically formulated to hygroscopically absorb any water-based coolant remaining in the cooling system after initial drain. Because certain parts of the cooling system might not drain out with gravity, and it would take too long to disconnect every pipe etc., installing a scavenging fluid is the most practical method of removing all the water-based coolant.

The Prep Fluid is not formulated to chemically clean the engine of rust and scale, but the process of circulation and draining will help remove any loose sediment.

Evans Prep Fluid must be used before converting from a water based coolant to Evans Waterless Engine Coolant.

2 x 5 Litre cans will be required to fill a full cooling system of most RX-7’s or RX-8’s
We are offering a Discounts for 2 bottle packs plus combined delivery discount if buying two bottles together to be shipped to a UK Mainland address, Simply select your desired quantity from the drop down menu.

Evans Power Cool 180 is the coolant of choice for many professional racing teams and performance car specialists. For use in all performance car engines primarily fabricated from aluminium, plus some steel and copper components.

Conversion from a water-based coolant to Evans is a straight forward process that can be undertaken by anyone with some basic experience in engine mechanics.

The primary objective of converting to Evans Waterless Engine Coolant is to eliminate all of the problems associated to water:

Eliminates Overheating
Evans Waterless Coolants have a boiling point above 180°C and will not vaporise, thus eliminating overheating, boil-over and after-boil.

Reduces Pressure
Evans Waterless Coolants generate very low vapour pressures reducing strain on engine hoses and cooling system components.

Prevents Corrosion
Water promotes corrosion via oxidation and electrolysis. Evans Waterless Coolants contain no oxygen and are virtually non-conductive effectively preventing corrosion.

Maximise BHP
Evans Waterless Coolants eliminate pre-ignition and detonation caused by overheating – thus increasing combustion efficiency and delivering more power.

Stops Erosion
Evans Waterless Coolants stop cavitation and eliminate liner and cooling pump erosion.

Freeze Protection
Evans Waterless Coolants freeze below -40ºC

Non-Toxic
Evans Waterless Coolants are proven to be Non-Toxic. Standard anti-freeze is toxic and known to kill pets.

If the engine to be converted is currently filled with a water-based coolant an important part of a good installation is using Evans Prep Fluid. Prep Fluid is specifically formulated to purge remaining water-based antifreeze from the system after initial drain. Evans Prep Fluid is sold separately and available just below.

2 x 5 Litre cans will be required to fill a full cooling system of most RX-7’s or RX-8’s
We are offering a Discounts for 2 bottle packs plus combined delivery discount if buying two bottles together to be shipped to a UK Mainland address, Simply select your desired quantity from the drop down menu.

Finding a front strut brace for the First Generation RX-7 FB these days was pretty much impossible. Then In steps Whiteline suspension with their Aluminium front strut brace, Well made a stupidly affordable.
You can never have too much chassis stiffness. Weight aside, the more the better. Chassis bracing maintains alignment angles and spring rates by greatly reducing body or chassis flex. In fact, it helps every component in the suspension system do its job properly and you can feel the difference through improved turn-in, sharper steering response along with greater steering feedback.
Part KBS608

Leave your cooling concerns behind with the installation of a chassis-specific KOYO Racing performance radiator for the Manual Transmission 1983-85 RX-7 12A. The KOYO Radiators (1-7/8″ or 48mm) single-pass radiator provides improved cooling coverage for both street and track applications.

Construction is held to tight quality control standards that are illustrated in the outstanding Heliarc soldering, pristine tube and fin alignment, and mirror-like surface finish. The tubes, fins, headers, and brackets are brazed in a state-of-the-art Nocolok furnace, which bonds these components into a virtually indestructible radiator unit.

All fan mounts are situated to OE specifications, and using the OEM mounting locations facilitates fitment into the RX-7.

Specifications:
16-3/4″ H x 22″ W x 1-7/8″ TH
– MT only – Auto transmission models required the installation of an external transmission oil cooler.

Koyo USA Part Number – HH063144

Special order item only, please contact us in advance prior to ordering as these can take up to 3 months as they are normally made to order.

An excellent upgrade for your old, tired or failed ignition coils in your RX-7 FB or FC ECI. These MSD coils offer very high voltage output of up to 45’000 volts.
MSD ignition Coil, Blaster 2, with Ballast and Hardware

Blaster 2 Coil, w/Ballast & Hardware

If you are looking to upgrade your stock coil or want to complement the performance of your MSD 6-Series Ignitions, our blaster coils are the right choice. For MSD Ignition applications. With a stock points style ignition, a ballast resistor must be placed in-line with the positive terminal of the coil. These blaster coils are supplied with a 0.8 ohm ballast resistor plus a terminal and boot to fit most applications. Mallory Melonite applications also require the ballast resistor.

• Performance upgrade for canister style coils
• High voltage and energy output
• Improved materials and turns ratio
• Improved performance
• A performance upgrade for points
• Comes with 0.8 ohm resistor; fits most applications
• CARB approved legal for use in all states
• Use with stock or MSD 6-Series Ignitions

A great upgrade option for your failed OEM coils on an early rotary engine.
MSD ignition Coil, Blaster 2, High Performance

Blaster 2 Coil

The blaster coils share the same special windings and high voltage output but do not include a ballast resistor.
When you are using an MSD Ignition control, the ignition is responsible for delivering the voltage to the coil so a ballast resistor is not necessary.

• Low resistance and improved turns ratio produces a powerful spark for improved performance
• Special windings and high voltage output; does not include a ballast resistor
• Sturdy metal housing is finished in red
• OBD II and CARB approved; legal for use in all states; D-40-37

AEM’s Water/Methanol Injection Filter can filter particulates as small as 40 microns. It protects the working parts of the water/methanol system and the engine from particulates in the water/methanol mixture when installed in-line before the water/methanol pump, and can be used on virtually any water/methanol injection system using ¼” OD tubing.

Why An Inline Filter Is A Good Idea.

If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4″ OD nylon tubing, so it fits most Water/Methanol injection kits on the market today!

• Simple to install, takes less than a minute!
• Fits virtually every Water/Methanol system on the market.
• Polypropylene housing – rugged material that is compatible with high concentrations of methanol.
• Completely Serviceable Assembly – can be disassembled, cleaned and reused for a long service life.
• Stainless Steel mesh strainer – AEMs custom mesh strainer filters down to 40 microns – MUCH smaller than similar filters.
• Large Filtering Area assure long service life and does not significantly reduce flow.
• Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.

AEM PART NUMBER – 30-3003

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Please select your desired tank size from the drop down menu before adding your selection to the shopping cart

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3300 Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM’s Boost Dependent, PN 30-3300 gasoline Water/Methanol Injection System’s compact 1 gallon tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM Part Numbers
V2 Water Methanol Kit With 4 Liter Tank – 30-3300
V2 Water Methanol Kit With 19 Liter Tank – 30-3301