Possibly The Best Rotary Premix You Can Buy
Inherently with many rotary engines, the entirety of the rotor and housing are not being sufficiently lubricated, resulting in premature wear or damage. In order to increase lubrication within the rotary, Idemitsu developed Idemitsu Rotary Premix.  At 1/2 oz per gallon of fuel, it is a cost effective way lubricate more of your engine and prevent premature catastrophic damage.

• A special blend of base oils reduces deposits and subsequent exhaust port clogging. As a result, your rotary will maintain the power at which it was designed.
• Special detergent/dispersant additives keep you fuel injectors clean to reduce maintenance.
• Provides additional lubrication for apex and side seals to increase seal life and increase efficiency of engine.
• Special additives allow for better sealing of the chamber, creating greater efficiency and more power.
• Idemitsu Lubricants America Corporation recommends the use of the Ratio Rite Measuring cup to ensure a proper mixture of Premix Rotary Fuel Lube and gasoline.

A full synthetic oil specially formulated for your rotary engine from Idemitdu Each Bottle contains 1 US Quart of Oil

Pack discounts for 6 bottle packs and 12 bottle packs can be purchased via our Idemitsu Shop

A Full Synthetic Oil SAFE for your Rotary Engine
Do you feel that you aren’t getting the power you should be from your rotary engine? Are you experiencing bearing wear under severe (or possibly under not-so-severe) operating conditions? If so, you may be using the wrong engine oil. Idemitsu 20W-50 can reduce or even eliminate some of the problems you may be having. As the developer of the engine oil for the winning 1991 LeMans Mazda 787B and a long time supplier of vital lubricants to Mazda, Idemitsu has intimate knowledge of the requirements of rotary engines.

• With the precise base oil mix of PolyAlphaOlephins and PolyEsters, Idemitsu Rotary Engine Oils are able to minimize those deposits on your apex seals. 
• Allows for better sealing of the chamber, facilitating more power generation. 
• Extends the life of turbochargers by reducing bearing coking.
• Specially developed additives facilitate even tooth load on the front stationary gear to allow for higher loads and higher RPM.
• Premium anti-wear agents create a strong film between the main bearings and the eccentric shaft, reducing metal-to-metal contact and minimizing bearing wear.
• Developed to reduce entrained gas generation. Entrained gases reduce the oils ability to prevent metal-on-metal contact, thereby increasing main bearing wear.
• Includes Molybdenum as a friction modifier. This compound reacts with the metal surfaces to create a low-shear boundary. The low shear characteristic reduces friction, increasing efficiency and power output. 

A full synthetic oil specially formulated for your rotary engine from Idemitdu Each Bottle contains 1 US Quart of Oil  

A Full Synthetic Oil SAFE for your Rotary Engine
Do you feel that you aren’t getting the power you should be from your rotary engine? Are you experiencing bearing wear under severe (or possibly under not-so-severe) operating conditions? If so, you may be using the wrong engine oil. Idemitsu 10W-30 can reduce or even eliminate some of the problems you may be having.
As the developer of the engine oil for the winning 1991 LeMans Mazda 787B and a long time supplier of vital lubricants to Mazda, Idemitsu has intimate knowledge of the requirements of rotary engines.

 

• With the precise base oil mix of PolyAlphaOlephins and PolyEsters, Idemitsu Rotary Engine Oils are able to minimize those deposits on your apex seals. 
• Allows for better sealing of the chamber, facilitating more power generation. 
• Extends the life of turbochargers by reducing bearing coking.
• Specially developed additives facilitate even tooth load on the front stationary gear to allow for higher loads and higher RPM.
• Premium anti-wear agents create a strong film between the main bearings and the eccentric shaft, reducing metal-to-metal contact and minimizing bearing wear.
• Developed to reduce entrained gas generation. Entrained gases reduce the oils ability to prevent metal-on-metal contact, thereby increasing main bearing wear.
• Includes Molybdenum as a friction modifier. This compound reacts with the metal surfaces to create a low-shear boundary. The low shear characteristic reduces friction, increasing efficiency and power output. 

A full synthetic oil specially formulated for your rotary engine from Idemitdu
Each Bottle contains 1 US Quart of Oil
 

Fully synthetic high boiling point brake fluid that is fully compatible with DOT3 and DOT4 Brake fluids recommended by Mazda.
DOT5.1 Brake fluid has a much higher boiling point then both DOT3 and DOT4 fluids making it an excellent alternative when renewing your brake and clutch fluid. as well as being very affordable when compared to many other high performance “race spec” fluids
We have been using this brake fluid in our own cars for many years with no issue even on long stints on track or drives through mountain passes where a lot of braking is required.

1 bottle should be sufficient to renew your brake system, however 2 bottles are usually recommended if your changing from a different fluid such as DOT3 or DOT4.
Specs:

• Type : 100% Synthetic
• Dry Boiling Point : 275℃
• Wet Boiling Point : 183℃
• Volume Per Bottle : 1000ml

5 Year Service Life
In an industry where its becoming more and more confusing to select something as simple as coolant for your car Essex Rotary have made it simple. We have carefully selected this super long life coolant for is compatibility with the materials that make up your Mazda Rotary engine. Premixed to reduce mess and minimize hassle.
A coolant specially selected for your rotary engine by the team here at Essex Rotary
Each bottle contains 5 liters of premixed coolant ready to go. A normal coolant change will require 2 bottles (10 liters in total) this should be more then enough to cover any rotary model you may have.

Cataclean is a rotary engine safe treatment that is simple to use.
Cataclean is primarily designed to help lower emissions and is very successful if your having trouble passing your MOT on emissions grounds, while this product cannot fix a broken fan it can breath new life in to a good catalytic converter that is not working at its best.
Used in a rotary engine it can also help keep carbon build up at bay, something we all know can be a killer of compression if your RX is not driven hard.
We recommend its used twice yearly for best results.

Set of 4 Magnecor KV85 (8.5mm) Performance HT leads for you RX-7 Fd3s

All Magnecor leads are covered by a 10 year guarantee which ensures long lasting reliability and service life.
Original equipment replacement. Designed to improve original ignition system performance on vehicles using either electronic engine management systems .
Conductor provides excellent RFI and EMI suppression to permanently eliminate the typical performance and fuel-wasting spark energy deterioration of OE and aftermarket carbon conductor wires.

4 Pulley kit Including Belts ideally suited for your RX-7 FD3s
Essex Rotary brings you this new lightweight under drive pulley Kit replaces all three main pulleys (Main Eccentyric Shaft Pulley, Alternator and Water Pump Pulleys) plus the Power Steering Pump Pulley, reducing the potential for Water Pump cavitation and over working of the Alternator at the high RPM ranges the Rotary Engine can operate at.

These Lightweight Pulleys are CNC machined from super light but extremely strong 6061-T6 Aluminium Alloy. reducing rotational weight from the crank and associated ancillaries will theoretically frees up horsepower normally used to turn the heavier pulleys and ancillaries (though Essex Rotary make no claim to proven HP gains when using under drive kits)

Cavitation
Cavitation is a process where by your water pump impeller acts like a “whisk” at high RPM beating air bubbles in to the coolant mixture, this process dramatically reduces coolant efficiency as the increasing cavitation effect reduces coolant flow around the engine.

Each kit comes with 2 new belts (alternator/water pump and air conditioning drive belts) made by Gates to suit your new setup as the OEM size belts will no longer fit.

This item is normally in stock however please allow up to 21 days for delivery of your kit if we are out of stock.
FREE DELIVERY CURRENTLY OFFERED ON THIS PRODUCT

Normal Price £64.99
Made to order, right here at Essex Rotary using all MSD Components.

The MSD 8.5 mm Super Conductor wire is the performance wire engineered from the inside out, the 8.5mm offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 In. length of Super Conductor wire there is only 40 to 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, MSD use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss of spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight, that there is over 40 Ft. of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) choke.

• Copper alloy conductor has a resistance value of less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• Forty feet of conductor is wound into a single foot of wire for high EMI suppression
• Conductor core features Dupont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

These MSD HT Leads are made to order right here at Essex Rotary HQ, from genuine MSD components. Available in Red or Black cable options (select your preferred color from the drop down menu before hitting the “add to cart” button.

Custom lengths and configurations available upon request.

A high quality replacement for the plastic collar found on the bottom of your shifter.

helping to reduce play in the shifter feel and increase the positive feeling of shifting gears.

An original R-Magic part direct from Japan.
Please not this is designed for use with 5 speed manual transmission gearboxes found in the RX-7 FD3s  and 192ps RX-8.
Not compatible with 6 speed RX-8 shifters.